SAUTER FK 500 Digital Force Gauge (500 N / 0.2 N)
€200.00
% Manufacturer's RRP: €285.00 29% below manufacturer's RRP
ⓘ This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.
Product information "SAUTER FK 500 Digital Force Gauge (500 N / 0.2 N)"
The Sauter FK 500 measures tensile and compressive forces up to 500 N and has a readability of 0.2 N. It is a handheld measuring device with an internal sensor that can also be bolted onto a test stand. Those who only need to measure force occasionally can simply hold it in their hand. Those carrying out series testing can mount it on a Sauter test stand rated up to 5 kN to achieve reproducible measurement conditions.
Measuring tensile and compressive forces
The instrument measures forces in both directions. The tolerance is 0.5 % of maximum, whilst the overload protection is set at 200 % of maximum. Measurements are taken at 1,000 Hz, allowing even brief force peaks to be recorded. In Peak-Hold mode, the display freezes the maximum value for around 10 seconds; in Track mode, the display follows the applied force. Selectable units are N, lbf, kg and ozf. The automatic switch-off (Auto-Power-Off) conserves battery power.
In practice, Peak-Hold is useful for tests where the maximum value is important, such as when disconnecting a connection or pressing a component until it fails. Track is suitable when a force needs to be monitored over the course of a movement, for example when pressing a switch.
Display and housing
The LCD has 18 mm high digits and, according to Kern, rotates automatically depending on how the device is held or installed. The plastic housing measures 195 x 84 x 35 mm and weighs approximately 0.65 kg net. Force is applied via an M8 external thread. Clamps with an M6 internal thread are compatible with the AFM 22 thread adapter (M8 internal thread, M6 external thread), which is also available.
Power supply
The scope of delivery includes a mains adaptor and six AA batteries (1.5 V). According to the data sheet, the device operates for approximately 25 hours on batteries, after which it can be switched to mains power. Country-specific adaptors for the EU, UK, US and Switzerland are included with the mains adaptor. The ambient temperature should be between 10 °C and 30 °C.
Typical applications
- Test laboratories and research and development: tensile force of joints, compressive force of springs and components
- Automotive industry: actuation forces of switches, levers and fasteners
- Maintenance and servicing: testing of springs, latches and adjustment forces
- Plastics engineering: pull-off and tear forces on small parts
The FK 500 covers the range up to 500 N. For testing higher forces, use the FK 1K with a capacity of 1,000 N and a readability of 0.5 N. If you require finer readability at 500 N, the FC 500 offers a readability of 0.1 N and a tolerance of 0.3 %.
Practical advice
The force should be applied in the axial direction of the device. Lateral forces place a strain on the sensor and distort the reading. On a test stand, the axis can be kept aligned easily; by hand this is more difficult.
Regulatory information
As an electrical device, the device falls under the ElektroG. The manufacturer Kern & Sohn GmbH is registered under the WEEE registration number DE 80821200. How to return old appliances is described on the page Environment and disposal.
Frequently asked questions
Is the FK 500 compatible with a test stand?
Yes, according to Kern, it is compatible with all Sauter test stands up to 5 kN. The force application point is an M8 external thread.
Can I connect clamps with an M6 thread?
Yes, using the AFM 22 thread adapter (M8 internal thread, M6 external thread).
Are the batteries included in the scope of delivery?
Yes, six 1.5 V AA batteries are included, as well as the mains adaptor.
Are calibration certificates available?
Factory and DAkkS calibration certificates are also available, separately for tension, compression and both directions.
How long is the warranty?
According to Kern & Sohn, this device comes with a 2-year warranty. Kern grants 3 years on products with a list price of €500 or more and 2 years on products below that and on components; wear parts such as batteries and rechargeable batteries are excluded. Warranty repairs are carried out by Kern or by a Kern dealer.
Technical details
| Measuring range (max) | 500 N |
|---|---|
| Readability (d) | 0.2 N |
| Force direction | Tension and compression |
| Tolerance | 0.5 % of maximum |
| Overload protection | 200 % of maximum |
| Measurement frequency | 1,000 Hz |
| Functions | Hold, Peak, Track, Auto-Power-Off |
| Units | N, lbf, kg, ozf |
| Display | LCD, digit height 18 mm, rotatable |
| Force application | M8 external thread |
| Housing (W x D x H) | 195 x 84 x 35 mm, plastic |
| Power supply | Mains adaptor or 6 x 1.5 V AA |
| Battery life | approx. 25 h |
| Ambient temperature | 10 °C to 30 °C |
| Net weight | approx. 0.65 kg |
Scope of delivery
- Sauter FK 500 force gauge
- Standard attachments, as shown in the product image
- 90 mm extension rod
- Mains adaptor with plug adaptors for the EU, UK, US and Switzerland
- 6 AA batteries (1.5 V)
Individual requirements and procurement service
Clamps, a handle, threaded adaptors, a tensiometer attachment and a carrying case are also available. Factory and DAkkS calibration certificates are available for tension, compression and combined tension and compression. Enquiries are handled via our procurement service.