Skip to main content Skip to search Skip to main navigation

IKA ICC control Immersion Circulator, TFT Display, up to 150 °C, 0004136600

ⓘ  This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.

Product information "IKA ICC control Immersion Circulator, TFT Display, up to 150 °C, 0004136600"

The ICC control is a compact immersion circulator for temperature control of liquids in open or semi-open bath vessels up to 150 °C. It has a TFT display, a temperature stability of ±0.01 K according to DIN 12876 and an integrated pressure/suction pump. The bath vessel is not included in the scope of delivery, and the circulator is clamped to an existing vessel.

Mounting on the bath vessel

The circulator is attached to the bath vessel with a holding clip, and the clamping width of the universal clamp is 0 to 40 mm. The vessel must be at least 150 mm deep. The circulator measures 145 x 340 x 200 mm and weighs 3.75 kg, and a carrying handle and an integrated stand are part of the housing. The permissible duty cycle is 100 %.

Control, display and programs

The circulator controls by PID, a PT 100 measures the working temperature and a PT1000 the safety temperature. The TFT display shows both values, and the display resolution is 0.01 K. The set temperature can be set to an accuracy of 0.1 K. There is a connection for an external PT 100 probe, and the display indicates operation with an external probe. The device can store 10 individual procedures with up to 10 steps each.

Pump and cooling

The pressure/suction pump is intended for internal and external applications and its output can be varied. It delivers up to 18 l/min at 0 bar back pressure, the maximum pump pressure is 0.3 bar, and on the suction side 0.2 bar. For temperature control below or near ambient temperature, a cooling coil is optionally provided, and with external cooling the minimum operating temperature is -20 °C.

Connection and environment

The circulator runs on 230 V at 50/60 Hz and draws 2,100 W, of which 2,000 W is heating power. It is protected to IP 21, and the permissible ambient temperature is 5 to 40 °C at no more than 80 % relative humidity. The device includes a calibration option.

Safety equipment

An adjustable safety circuit ranges from 0 to 160 °C. Visual and audible warnings, the over-temperature warning and protection against low and high level are built in. The circulator is classified as DIN 12876 class III and marked FL.

As a package with bath

IKA combines the ICC control with plastic and stainless steel baths to form ready-to-connect packages. The ICC control eco 8 and the ICC control eco 18 contain circulator, bath and bath bridge, and the ICC control eco 8 c also includes a cover, pump connection set, cooling coil and PT 100.30 probe. The plastic baths are intended for water up to 100 °C. The ICC basic circulator has an LED display instead of TFT and a temperature stability of ±0.02 K.

Typical applications

  • Temperature control of liquids in open or semi-open bath vessels up to 150 °C
  • Internal or external applications with the integrated pump
  • Temperature control with external PT 100 probe
  • Programs with up to 10 steps
  • Control and monitoring via RS 232 or Micro-USB with the IKA labworldsoft software

Technical details

Heating power2,000 W
Working temperatureRoom temp. +10 K at 1,000 rpm to 150 °C
Operating temperature min. (with external cooling)-20 °C
Temperature controlPID
Working and safety probePT 100 (working temperature), PT1000 (safety temperature)
Display of working/safety temperatureTFT
Temperature stability according to DIN 12876±0.01 K
Display resolution0.01 K
Setting accuracy of set temperature0.1 K
Connection for external temperature probePT 100
Indication of operation with external probeyes
Pump typePressure/suction pump, output variable
Max. flow rate (0 bar back pressure)18 l/min
Max. pump pressure (no flow)0.3 bar
Max. pump pressure suction side (no flow)0.2 bar
Classification according to DIN 12876III with FL marking
Warning functionsvisual, audible, over-temperature
Safety circuit, adjustable0 to 160 °C
Low/high level protectionyes
Calibrationyes
Min. bath depth150 mm
Device mountingClamp
Clamping width of universal clamp0 to 40 mm
Dimensions (W x H x D)145 x 340 x 200 mm
Weight3.75 kg
Permissible duty cycle100 %
Ambient temperature5 to 40 °C
Relative humiditymax. 80 %
IP rating (DIN EN 60529)IP 21
InterfacesRS 232, Micro-USB
Power supply230 V, 50/60 Hz
Power consumption2,100 W

Scope of delivery

  • 1 x ICC control Compact Immersion Circulator with holding clip (universal clamp)
  • 1 x Screwdriver
  • 1 x USB cable USB A to Micro-B, 2 m

The bath vessel is not included in the scope of delivery.

Regulatory information

This device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, IKA, is DE 66784213. Information on the return of old appliances can be found on our page Environment and disposal.

Warranty and procurement service

The IKA manufacturer's warranty of 2 years applies to the ICC control, extended to 3 years on registration at ika.com/register within 90 days of purchase. On request we procure cooling coils, bath vessels, covers and other accessories.

Certification marks: NRTL (TÜV SÜD, USA/Canada)