Skip to main content Skip to search Skip to main navigation

IKA T 18 digital ULTRA-TURRAX disperser, tool-free drive unit, 500 W, 0003720000

Scope of delivery: T 18 digital drive unit. The dispersing tool shown is not included and is available separately.

ⓘ  This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.

Product information "IKA T 18 digital ULTRA-TURRAX disperser, tool-free drive unit, 500 W, 0003720000"

Anyone who frequently homogenises samples in the laboratory will be familiar with the problem: a good drive alone is not enough; ultimately, it is the right tool that determines the final fineness and throughput. The IKA T 18 digital ULTRA-TURRAX (0003720000) is designed precisely with this in mind. It is supplied as a drive unit only, with a power consumption of 500 watts, which can be freely combined with various S-18 tools for coarse, fine or single-use applications. The LED display always shows the set speed between 3,000 and 25,000 revolutions per minute, which facilitates reproducible results across multiple test runs.

Rotor-stator principle with high shear rates

During dispersion, the tool draws the sample in axially and forces it out radially through the narrow slots between the rotor and stator. This briefly generates very high shear rates, which break down solid components and mix liquids into stable emulsions or suspensions. With an output power of 300 watts and a processable volume of 0.001 to 1.5 litres (based on water), the T 18 digital covers typical laboratory batches up to a maximum viscosity of 5,000 mPas.

Stepless speed control with LED display

The speed can be adjusted continuously between 3,000 and 25,000 rpm, with a deviation of just 1 % according to IKA. Unlike purely analogue controllers, the LED display shows the set value directly. Once process parameters have been determined, they can be noted down and reproduced exactly for subsequent experiments. With a permissible duty cycle of 100 %, prolonged continuous operation is also possible without the drive having to pause in between.

The choice of tool determines the result

The T 18 digital is deliberately supplied without a dispersing tool, as the most suitable tool depends heavily on the specific sample. The standard S 18 N - 19 G tool with PTFE bearings is suitable for coarse pre-shredding and tougher media, whilst the S 18 N - 10 G offers a narrower gap geometry for finer end products. Those who frequently work with varying samples that are potentially susceptible to contamination will find disposable plastic tools to be a practical alternative, as they reduce the risk of cross-contamination between batches.

Typical applications

As a standalone drive unit, the T 18 digital is particularly suitable for laboratories that already work with a variety of tools or switch specifically between several applications:

  • Preparation of emulsions and suspensions in sample preparation
  • Homogenisation of tissue samples in biology and life sciences research
  • Mixing pigments and fillers into dispersions
  • Routine tasks in quality assurance with varying tool configurations
  • Setting up customised workstations through flexible combination with a stand and tool

Selection guide for the T-18 range

Drive unit only, complete set or just the tool? The four products compared here differ primarily in terms of what is included in the scope of delivery and, in the case of the mini-drive, in terms of motor power.

ProductTypeMotor power (input/output)Speed rangeScope of delivery
T 18 digital ULTRA-TURRAX (this product)Drive unit500 W / 300 W3,000 to 25,000 rpmDrive unit only, without tools
T 18 digital SolutionSet500 W / 300 W3,000 to 25,000 rpmDrive unit, S 18 N - 19 G tool, stand, boss head
T 18 mini digital SolutionSet, compact drive210 W / 160 W3,000 to 25,000 rpmDrive unit, tool S 18 N - 19 G, stand, boss head
S 18 N - 19 G dispersing toolSingle toolNo built-in motorPermitted up to 25,000 rpmTool only

Anyone who already owns a T-18 drive or wishes to switch between several tools as required is best served by the drive described here, which does not require a tool. The complete T 18 digital Solution Set is suitable for getting started straight away without having to order a separate tool; those looking for a more compact workstation will find the T 18 mini digital Solution to be a suitable alternative with lower motor power.

Technical details

Motor power input500 W
Motor power output300 W
Processing volume (H₂O)0.001 to 1.5 l
Max. viscosity5,000 mPas
Speed range3,000 to 25,000 rpm, continuously variable
Speed deviation1 %
Speed displayLED
Noise level without tools75 dB(A)
Support arm diameter13 mm
Support arm length160 mm
Process typeBatch
Permissible duty cycle100 %
Permissible ambient temperature range5 to 40 °C
Permissible relative humidity80 % (up to 31 °C), decreasing linearly to a maximum of 50 % (at 40 °C)
Dimensions (W x H x D)87 x 271 x 106 mm
Weight2.5 kg
Connected load220 to 240 V, 50/60 Hz, 500 W (other voltage options from 100 to 120 V available)
IP ratingIP 20 (DIN EN 60529)

Scope of delivery

  • 1 x IKA T 18 digital ULTRA-TURRAX (drive unit, without dispersing tool)

The dispersing tool and stand are not included and must be purchased separately to suit the specific application.

Differences from the neighbouring series

If you also require a brushless motor with a timer, the IKA T 18 brushless series offers the next step up: the T 18 brushless digital ULTRA-TURRAX as a drive unit without a tool, or the T 18 brushless digital Solution as a complete set. Both drive units operate with lower wear than the classic T 18 digital. An overview of all dispersers can be found in the ‘Dispersers’ category; suitable tools are listed under ‘Dispersing Tools’.

Application, set-up and maintenance

For short-term manual operation, the T 18 digital fits comfortably in the hand; for longer or reproducible processes, it can be securely mounted on a stand, such as the R 1826 plate stand. Operation is permitted at an ambient temperature of 5 to 40 °C and a relative humidity of up to 80 % at 31 °C, decreasing linearly to a maximum of 50 % at 40 °C. The drive, with degree of protection IP 20, is not designed for use in damp rooms or outdoors. After each use, the tool used should be dismantled and, depending on the material, cleaned or sterilised before the next procedure begins. At the end of its service life, as an electrical appliance, the drive must not be disposed of with household waste but must be placed in the separate collection for waste electrical and electronic equipment.

Warranty

Manufacturer’s warranty from IKA: 2 years, extended to 3 years upon registration at ika.com/register within 90 days of purchase.

Regulatory information

This device is an electrical appliance within the meaning of the German Electrical and Electronic Equipment Act (ElektroG). The WEEE registration number of the manufacturer, IKA, is DE 66784213. Information on the return of old appliances can be found on our page Environment and disposal.

Individual requirements & procurement service

In addition to the standard tools, further accessories for the T 18 digital are also available, such as stands, mounting elements or the Silentstream flow breaker to reduce air ingress during dispersion. Do you require a specific tool, a qualification document or assistance in selecting the right configuration? Through our procurement service, we can assist you with procurement and configuration.

Frequently Asked Questions

Is a dispersing tool included in the scope of delivery?
No, the T 18 digital is supplied exclusively as a drive unit. A suitable tool, such as the S 18 N - 19 G, must be purchased separately.

Which tool is suitable for coarse pre-grinding?
For coarse applications and tougher media, the S 18 N - 19 G with PTFE bearings is the standard choice; finer end products can be achieved with the S 18 N - 10 G.

How accurately can the speed be reproduced?
The LED display shows the set value within a range of 3,000 to 25,000 rpm with a deviation of around 1 %, which facilitates the exact repetition of test series.

Is a stand included in the scope of delivery?
No; for continuous operation, we recommend a separately available stand such as the R 1826 plate stand.

What is the difference between the T 18 digital and the T 18 mini digital Solution?
The T 18 mini digital Solution features a more compact, brushless drive with lower motor power and comes as a set including the tool and stand; the T 18 digital described here is the more powerful drive unit without accessories.

Skip product gallery

Matching accessories

Discount
Topseller
In stock
IKA dispersing tool S 18 N - 10 G, Ø 10 mm, L004639
IKA dispersing tool S 18 N - 10 G, Ø 10 mm, L004639
Manufacturer number: L004639
Sale price: €1,007.25
RRP €1,343.00 25% below manufacturer's RRP
Discount
Topseller
In stock
IKA S 18 N - 19 G Dispersing tool, coarse, PTFE bearings, 10 to 1,500 ml, L004640
IKA S 18 N - 19 G Dispersing tool, coarse, PTFE bearings, 10 to 1,500 ml, L004640
Manufacturer number: L004640
Sale price: €1,007.25
RRP €1,343.00 25% below manufacturer's RRP
Discount In stock
IKA S 18/25-ET50 disposable tube, 50 ml, for S 18 D / S 25 D, 0003452500
IKA S 18/25-ET50 disposable tube, 50 ml, for S 18 D / S 25 D, 0003452500
Manufacturer number: 0003452500
Sale price: €8.10
RRP €9.00 10% below manufacturer's RRP
Discount Promo In stock
IKA S 18 D - 10 G - KS disposable dispersing tool (12 pieces), plastic, Ø 10 mm, 0003452400
IKA S 18 D - 10 G - KS disposable dispersing tool (12 pieces), plastic, Ø 10 mm, 0003452400
Manufacturer number: 0003452400

Content: 12 piece(s) (€25.13 / 1 piece(s))

Sale price: €301.50
RRP €335.00 10% below manufacturer's RRP
Discount Promo In stock
IKA S 18 D - 14 G - KS disposable dispersing tool (12 pieces), plastic, Ø 14 mm, 0003452300
IKA S 18 D - 14 G - KS disposable dispersing tool (12 pieces), plastic, Ø 14 mm, 0003452300
Manufacturer number: 0003452300

Content: 12 piece(s) (€25.13 / 1 piece(s))

Sale price: €301.50
RRP €335.00 10% below manufacturer's RRP
Discount In stock
IKA Silentstream flow breaker for dispersers, minimises air ingress, 0003754000
IKA Silentstream flow breaker for dispersers, minimises air ingress, 0003754000
Manufacturer number: 0003754000
Sale price: €21.00
RRP €28.00 25% below manufacturer's RRP