Skip to main content Skip to search Skip to main navigation

IKA TS 25-3 Cleaning tool, cleaning tool for T 25 disperser, 0020003013

ⓘ  This product description has been translated from German using AI. Despite careful review, we do not guarantee that the translation is error-free; in case of doubt, the German version shall prevail.

Product information "IKA TS 25-3 Cleaning tool, cleaning tool for T 25 disperser, 0020003013"

Maximum analytical reliability through impeccable hygiene: the IKA TS 25-3 Cleaning tool

In modern laboratory practice, be it in strictly regulated pharmaceutical quality control, highly sensitive food analysis or microbiological research, sample preparation is a critical step. High-performance dispersing tools break down tissue, emulsify oils or suspend powders using immense shear forces. In the process, microscopically small sample particles are inevitably forced deep into the narrow gap between the rotor and stator, as well as into the tool’s internal plain bearings. If these residues are not removed after every single sample, there is a risk of the dreaded cross-contamination (carry-over). Even invisible traces of DNA, allergens or active pharmaceutical ingredients from the previous sample can skew the subsequent analysis. Manually scrubbing the sharp-edged tools under running water is time-consuming and can involve a risk of injury to laboratory staff. To standardise this essential cleaning process, make it safer and speed it up, IKA has developed the TS 25-3 Cleaning tool (MPN 0020003013). This cleaning system is intended for users of the T 25 disperser series who have high requirements for the cleanliness of their instruments.

The systematic 3-stage cleaning procedure

At the heart of the IKA TS 25-3 system lies not only the hardware itself, but also the establishment of a validatable Standard Operating Procedure (SOP) for your laboratory. With this tool, IKA recommends a defined cleaning process comprising three consecutive steps:

  1. Pre-cleaning (solvent): In the first step, coarse contamination is removed. The contaminated dispersing tool is inserted into the first tube, which is filled with a solvent suitable for your sample. Switching on the dispersing drive creates a powerful suction that forces the solvent through the shear gap with high kinetic energy, mechanically and chemically dislodging even stubborn, greasy or sticky residues.
  2. Main cleaning (cleaning agent): In the second step, you move on to the next tube, which is filled with a specific laboratory cleaning agent (surfactant mixture). Here, proteins are denatured, fats are emulsified and any remaining organic or inorganic deposits are separated from the tool’s high-quality stainless steel at a molecular level.
  3. Final cleaning (rinsing): The third and final step takes place in the last tube, which contains pure, demineralised water. This rinsing cycle thoroughly washes all remaining traces of the previously used solvents and cleaning agents out of the tool. The result is a rinsed dispersing tool that is ready for the next sample.

Occupational health and safety at the highest level

In addition to analytical purity, the TS 25-3 Cleaning tool offers an advantage in terms of occupational health and safety. When solvents or aggressive surfactants are dispersed openly in a beaker to clean a tool, dangerous aerosols are inevitably produced, which can be inhaled by laboratory staff. The TS 25-3 system reduces this hazard. The ingenious tube holder secures the three supplied tubes firmly and stably. Thanks to the matching caps, the cleaning process takes place in a largely enclosed system. The caps reduce the spraying out of solvents or cleaning solutions. It also eliminates the need for dangerous manual handling with brushes near the razor-sharp, rotating blades of the dispersing tool.

Comprehensive compatibility with the T 25 ecosystem

The TS 25-3 Cleaning tool is designed exclusively for use in combination with the dispersers of the T 25 class, namely the T 25 digital and the drives T 25 easy clean digital and T 25 easy clean control. In terms of tools, the system covers an enormous range. It has been specifically developed for cleaning a wide variety of stainless steel dispersing tools, including models from the S 25 N series (e.g. S25N-18G/18G-ST, S25N-25G/F/25G-ST), the S 25 KR series (e.g. S25KR-18G/18G-ST, S25KR-25G/25F/25G-ST) and the vacuum-tight S 25 KV series (S25KV-18G/25G/25F).

Cost-effectiveness and Total Cost of Ownership (TCO)

At first glance, a specialised cleaning tool may seem like nothing more than a luxury item. However, if a detailed full-cost analysis is carried out, the TS 25-3 can pay for itself in laboratories with high sample throughput. Laboratory staff no longer have to stand at the sink for minutes on end and can save working time. In addition, the service life of your dispersing tools may be extended. Improper manual cleaning often leads to microscopic scratches on the stator or damage to the sensitive plain bearings caused by dried-on sample residues. Hydrodynamic cleaning in the TS 25-3 can be gentle on the material and can thus lower your ongoing spare parts costs. Investing in the IKA TS 25-3 Cleaning tool means investing in process reliability, the protection of your staff and reliable analytical results.

Technical data

  • System type: 3-stage cleaning system for dispersing tools
  • Cleaning phases: 1. Solvent, 2. Cleaning agent, 3. Demineralised water
  • Compatible drive motors: IKA T 25 digital, T 25 easy clean digital, T 25 easy clean control
  • Compatible tools (selection): S 25 N series (18G, 25G, 25F), S 25 KR series, S 25 KV series
  • Health and safety benefit: Reduces aerosol formation and contact with sharp rotor blades
  • Analytical benefit: Reduces the risk of cross-contamination (carry-over)

Scope of delivery

  • 1 x tube holder (sturdy base)
  • 3 x cleaning tubes
  • 3 x caps (for splash and aerosol protection)

(Please note: The dispersing drive and the dispersing tools are not included in the scope of delivery!)

Individual requirements & accessories

Have you switched to the newer generation of ‘easy clean’ (EC) tools in your laboratory, which can be cleaned without any dismantling? For machine cleaning in the laboratory dishwasher, we recommend the IKA HS 25 EC - DW Holder as a supplementary item. Do you work with highly infectious samples and wish to avoid cleaning altogether? In that case, we would be happy to advise you on IKA’s single-use plastic tools. Please feel free to contact our expert procurement service at any time for a bespoke optimisation of your laboratory processes.

Skip product gallery

Fits

Discount
Topseller
In stock
IKA T 25 digital ULTRA-TURRAX Dispergierer, 1 bis 2.000 ml, 3.000 bis 25.000 rpm, 0003725000, Produktansicht
IKA T 25 digital ULTRA-TURRAX disperser, 1 to 2,000 ml, 3,000 to 25,000 rpm, 0003725000
Manufacturer number: 0003725000
Sale price: €2,010.00
RRP €2,680.00 25% below manufacturer's RRP
Discount In stock
IKA T 25 easy clean digital ULTRA-TURRAX Dispergierer, 1 bis 2.000 ml, 3.000 bis 25.000 rpm, 0025002560, Produktansicht
IKA T 25 easy clean digital ULTRA-TURRAX disperser, 1 to 2,000 ml, 3,000 to 25,000 rpm, 0025002560
Manufacturer number: 0025002560
Sale price: €1,972.50
RRP €2,630.00 25% below manufacturer's RRP